If you are unable to get the lock bolt to extend the lock will need to be replaced. Please contact your safe manufacturer for all information relating to warranty and repair. NOTE: If the ribbon cable has been damaged beyond repair, the lock will have to be replaced. Safe Accessories Safes & Vaults Shotgun Parts weve replaced battery and still wont open Winchester Ammunition ft. If a boltwork issue is suspected, the boltwork may need to be adjusted. If a malfunction is suspected in the keypad, replace the keypad and re-try. Unplug the cable from the keypad then plug it back in. If there are any hard bends or crimping, please straighten them out. Insert the Sentry key in the keyhole and turn it counter-clockwise as opposed to clockwise. Replace your battery(s) with Fresh 9 volt alkaline (Duracell batteries are recommended. Why wont my sentry safe open with the key If the key doesnt seem to open the Sentry Safe, it may have been turned in the wrong direction. The safe boltwork may be blocking the lock bolt from extending.ġ. There could have been damage to the lock’s ribbon cable during installation.
When either the former or latter results in a lockout, usually the only option available to open the safe is to drill it. This could be an indication that the lock has an electronic short. Lock mounting bolts that have not been installed with Loctite loosen overtime and eventually fall into the wheel pack or cause an external relocker to fire. The battery(s) in your keypad could be low. You must think twice before you take this step.I close my safe door it will not lock back. One of the negative effects of drilling is that it can damage the safe. Once drilling is performed, you can then insert your finger to unlock the lock inside the safe. The bolts of the safe are jammed or misaligned. Try these before calling Sentry Safe Customer Service or a safe locksmith. Safes NYC experts can successfully perform its opening. Why does my Sentry Safe won't open Here are the most common reasons a Sentry Safe won't open. In order to open the safe through drilling, all you have to do is drill a small hole in a position where you can view the lock inside the safe. Performing a Gardall safe open without the combination can be a complicated situation. As a gun safe technician, I see both of these problems on a regular basis. Focus moving the paperclip or wire in that area until the gun safe opens. Listen to any sounds that indicate movement in the lock. Locate the area around the locking mechanism and press your ear close to the door. But, your electronic lock might also not be working properly if the battery doesn’t have enough amperage. Using a paperclip or thin piece of wire, work your way along the length of the gap on the front door. Typically this is because the battery is dead. Drilling can be an option when you have forgotten the combination to the safe or you lost the key. Battery failure is the most common reason the electronic lock on your gun safe isn’t working properly. Just before you consider drilling, you should call QuickPro Locksmith for an easier option.
This procedure should take few seconds or minutes to open the safe.ĭrilling is only recommended when there is no better option. Shake the knife a little and the lock will eventually open. To achieve this, simply make use of the tip of the knife and insert it into the keyhole. Opening the safe with a knife perhaps is the easiest way. Opening the safe with the aid of a knife or similar tool Rotate the screwdriver in a counter-clockwise movement until the lock of the safe opens. Make use of a screwdriver to open a safe without a keyįirst of all, you need to place the screwdriver on a flat surface, then insert the tip of the screwdriver inside the keyhole. Turn the tweezers along with the paper clip in an anti-clockwise position and continue turning until the lock is opened. With the aid of a tweezer, hold the paper clip in place, then insert the paper clip into the inner chamber of the lock- make sure the paper clip goes deeper into the lock. In order to use a paper clip to open the safe, just make sure the paper clip is straight, then insert the end of the clip into the upper part of the lock. Perhaps one of the easiest ways to open a safe without a key is to use a paper clip. Sometimes, it can be very easy to lose the key to the safe or even forget the combination numbers, but you should have an idea about the procedures to take in order to unlock the safe without the need for a key, these options include
Do not try to force a safe open with a key, if you don’t seem to open it the normal way, just call QuickPro Locksmith, and our professional technician will be right there at your doorstep to get it open very easily without the need for a key.